Difference between revisions of "Peripheral 2 Register"
From SpecNext official Wiki
m (turbo becomes CPU Speed) |
(updated to 78a6ee50) |
||
Line 8: | Line 8: | ||
! Bit !! Function | ! Bit !! Function | ||
|- | |- | ||
− | | 7 || Enable CPU speed mode key "F8", 0 = disabled (1 after Soft-reset) | + | | 7 || Enable CPU speed mode key "F8", and F5/F6 expansion bus hotkeys 0 = disabled (1 after Soft-reset) |
|- | |- | ||
| 6 || core3.1.2: Divert BEEP-only to internal speaker (hard reset = 0) | | 6 || core3.1.2: Divert BEEP-only to internal speaker (hard reset = 0) | ||
Line 15: | Line 15: | ||
| 5 || Enable "F3" key (50/60 Hz switch) (1 after Soft-reset) (was "Enable Lightpen" in core 2.0) | | 5 || Enable "F3" key (50/60 Hz switch) (1 after Soft-reset) (was "Enable Lightpen" in core 2.0) | ||
|- | |- | ||
− | | 4 || Enable | + | | 4 || Enable DivMMC NMI by DRIVE button (0 after Hard-reset) |
|- | |- | ||
| 3 || Enable multiface NMI by M1 button (hard reset = 0) | | 3 || Enable multiface NMI by M1 button (hard reset = 0) | ||
Line 21: | Line 21: | ||
| 2 || PS/2 mode (primary device: 0 = keyboard, 1 = mouse), exchanges the keyboard/mouse pins on the PS/2 connector (writeable only in config mode) | | 2 || PS/2 mode (primary device: 0 = keyboard, 1 = mouse), exchanges the keyboard/mouse pins on the PS/2 connector (writeable only in config mode) | ||
|- | |- | ||
− | | 1-0 || Audio chip mode (%00 = YM, %01 = AY, % | + | | 1-0 || Audio chip mode (%00 = YM, %01 = AY, %10 = ZXN-8950, %11 = Hold all AY in reset) |
(core 3.0) %11 hold all AY in reset | (core 3.0) %11 hold all AY in reset | ||
|} | |} |
Latest revision as of 11:02, 3 November 2024
Number | $06 |
---|---|
Readable | Yes |
Writable | Yes |
Short Description | Enables CPU Speed key, DivMMC, Multiface, Mouse and AY audio. |
Bit | Function |
---|---|
7 | Enable CPU speed mode key "F8", and F5/F6 expansion bus hotkeys 0 = disabled (1 after Soft-reset) |
6 | core3.1.2: Divert BEEP-only to internal speaker (hard reset = 0)
|
5 | Enable "F3" key (50/60 Hz switch) (1 after Soft-reset) (was "Enable Lightpen" in core 2.0) |
4 | Enable DivMMC NMI by DRIVE button (0 after Hard-reset) |
3 | Enable multiface NMI by M1 button (hard reset = 0) |
2 | PS/2 mode (primary device: 0 = keyboard, 1 = mouse), exchanges the keyboard/mouse pins on the PS/2 connector (writeable only in config mode) |
1-0 | Audio chip mode (%00 = YM, %01 = AY, %10 = ZXN-8950, %11 = Hold all AY in reset)
(core 3.0) %11 hold all AY in reset |
The bit 7 doesn't prevent SW from setting up different CPU speed by writing into CPU Speed Register ($07), it is used only to enable/disable the "F8" key toggle, similarly bit 5 enables "F3" key.
NEW in core 3.0:
bit 5 = enable F3 (50/60 Hz) bit 2 ps2mode only modifiable in config mode chip mode = 11 resets all AY
NEW in core 3.1.2:
bit 6 = BEEP-only into internal speaker (DMA does use two I/O ports now)